ISO 1114612021 激光器和激光相关设备 激光束宽度、发散角和光束传播比的测试方法 第1部分:散光和简单散光光束.pdf

ISO 11146-1-2021 激光器和激光相关设备 激光束宽度、发散角和光束传播比的测试方法 第1部分:散光和简单散光光束.pdf文档页数:22文档大小:9.38MB文档格式:pdf INTERNATIONAL ISO STANDARD 11146-1 Second edition 2021-07 Lasers and laser-related equipment- Test meth...

ISO 11146-1-2021 激光器和激光相关设备 激光束宽度、发散角和光束传播比的测试方法 第1部分:散光和简单散光光束.pdf

文档页数:22文档大小:9.38MB文档格式:pdf

INTERNATIONAL ISO STANDARD 11146-1 Second edition 2021-07 Lasers and laser-related equipment- Test methods for laser beam widths divergence angles and beam propagation ratios- Part 1: Stigmatic and simple astigmatic beams Lasers et equipements associes aux lasers-Methodes d'essai des largeurs du faisceau angles de divergence et facteurs de limite de diffraction- Partie 1:Faisceaux stigmatiques et astigmatiques simples Reference number ISO11146-1:2021(E) ISO ISO2021 ISO11146-1:2021(E) 1 COPYRIGHT PROTECTED DOCUMENT ©ISO2021 All rights reserved.Unless otherwise specified or required in the context of its implementation no part of this publication may be reproduced or utilized otherwise in any form or by any means electronic or mechanical including photocopying or posting on the internet or an intranet without prior written permission.Permission can be requested from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office CP 401.Ch.de Blandonnet 8 CH-1214 Vernier Geneva Phone:41227490111 Email:copyright@iso.org Website:.iso.org Published in Switzerland ii @ISO 2021-All rights reserved ISO11146-1:2021(E) Contents Page Foreword iv Introduction 1 Scope 1 2 Normative references 1 3 Terms and definitions...... 1 4 Coordinate systems 7 5 Test principles 7 5.1 Applicability 7 5.2 Beam widths and beam diameter. 7 5.3 Beam divergence angles. 8 5.4 Beam propagation ratios 8 5.5 Combined measurement of beam waist locations beam widths ...

本文来自孤浪王者投稿,不代表文丁图集立场,如若转载,请注明出处:https://www.2b34.com/blog/76369.html

打赏 微信扫一扫 微信扫一扫 支付宝扫一扫 支付宝扫一扫
() 0
上一篇 12-11
下一篇 12-11

相关推荐

  • T/CITSA 272022 智慧道路边缘计算网关通信接口规范.pdf

    T/CITSA 27-2022 智慧道路边缘计算网关通信接口规范.pdf文档页数:31文档大小:769.54KB文档格式:pdf T/CITSA 27-2022 ICS93.080.99 P51 团 体标准 T/CITSA 27-2022 智慧道路边缘计算网关通信接口规范 Edge puting gateway munication inter face standard of intelligent r

    2026-09-16 21:48:01
    900 0
  • JJF 14132013 轮胎压力表型式评价大纲.pdf

    JJF 1413-2013 轮胎压力表型式评价大纲.pdf文档页数:28文档大小:1.71MB文档格式:pdf 可可F 中华人民共和国国家计量技术规范 J143-3013 轮胎压力表型式评价大纲 Progran of Fatira of Tyre Gaage 201306-2有 2013-09-7买施 国家质量监督检验检疫总局布 轮胎压力表型式评价大

    2026-09-16 21:24:01
    269 0
  • QJ 4171978 莫氏锥体套规(0~6号).pdf

    QJ 417-1978 莫氏锥体套规(0~6号).pdf文档页数:3文档大小:916.74KB文档格式:pdf 中华人民共和国第七机械工业部 部标准 QJ417-78 莫氏锥体套规 0-6号 标适用于检验莫氏维度工具园锥GB1443一78外园锥的锥体套规. 一、型式 名称 图 页次 A型 不带扁尾的莫氏锥体套规 7 0~6

    2026-09-16 20:16:01
    883 0
  • JB/T 132072017 印刷机械 单张纸印刷品表面整饰机

    JB/T 13207-2017 印刷机械 单张纸印刷品表面整饰机附件大小:6.08MB附件格式:1个直链文件,格式为pdf 资源简介:ICS37.100.10J87 JB备案号:58451一2017中华人民共和国机械行业标准JB/T13207—2017印刷机械单张纸印刷品表面整饰机Printing machinery-Finishing machine for

    2026-09-16 20:08:01
    537 0

评论列表

联系我们

在线咨询: QQ交谈

邮件:admin@qq.com

工作时间:周一至周五,9:30-18:30,节假日休息

关注微信